材质 : | 聚氯乙烯 | 产品类别 : | 外墙装饰板 |
产品种类 : | 保温板 | 等级 : | B |
品牌 : | 筠尚 | 应用范围 : | XPS外墙保温系统 |
产地 : | 浙江.杭州 | 导热系数(常温) : | 0.035 |
低温弯折≤ : | 3.9 | 断裂伸长率 : | 450 |
抗弯强度 : | 590n | 抗压强度 : | 240n |
使用温度 : | 600 | 芯材 : | pvc |
形态 : | 条形 | 形状 : | 片状 |
安装方式 : | 螺钉 | 防火等级 : | B1级 |
廊坊彩钢板房屋外墙装修pvc挂板户外墙装饰材料筠尚筠尚公司32.8元一平米
受平聚氯乙烯加工中,捏合及其他加工性能和容积计量取决于粒径大小和分布,
较为理想的是具有均匀且粒径适当的树脂。
国标中规定筛余物的测定按照GB/T2916或附录B进行。若
有争议,以GB/T2916为仲裁方法。
(6)“鱼眼”数“鱼眼”是指通常加工条件下不塑化的透明
粒子,它是凝胶粒子。“鱼眼”影响薄膜的强度、电缆料的绝缘性
能、唱片的音质,因而很多产品要限制树脂的“鱼眼”数。对于大
多数制品,“鱼眼”数过多会使制品表面粗糙,而且还会降低整个
制品的物理性能,“鱼眼”处还有可能成为降解的中心,导致产品。
为了满足客户的需求,外墙装饰的 华、独特化,本公司新推出仿砖石、仿石板,
此异形板是在原有挂板的基础之上增加一定的生产工艺制成的。与挂板搭配使用。
1、 仿砖石的安装方法:
1在安装起始位置打好水平墨线。
2仿砖石由下向上安装,先安装仿砖石阴(阳)角,未折弯的阴(阳)角必须用工业热吹风机在中间线上进行上下烘烤,加热软化后可折成90度。
将 张阴(阳)角背面与墙面接触的地方打满密封胶,并且底边与水平墨线平对齐,直角边与墙角垂直后与墙体贴实, 后用钢钉在有圆形钉印的地方钉钉打实。钢钉采用镀锌水泥钉等,规格:φ2.0x20mm。
张阴(阳)打好胶,尤其下部边缘要涂满并压在 张阴(阳)角上部边缘,重合贴实然后钉钉。其他以此类推。
In the processing of PVC, kneading and other processing performance and volume measurement are dependent on the size and distribution of particle size, and it is ideal to have a uniform resin with appropriate particle size.
According to GB/T2916 or appendix B, the residue shall be determined.if
In case of any dispute, GB/T2916 shall be used as the arbitration method.
(6) "fisheye" number "fisheye" refers to the transparency that is not plasticized under normal processing conditions
Alpha particle, it's a gel particle."Fisheye" affects the strength of the film and the insulation of the cable material
Can, the sound quality of the record, so many products to limit the resin "fish eye" number.For large
Most products, "fish eyes" too much will make the surface of the products rough, but also reduce the whole
The physical properties of the product, the "fisheye" may also become the degradation center, resulting in the product.
In order to meet the needs of customers, the external wall decoration of the perfect hua, unique, the company launched a new copy masonry, copy SLATE, the special-shaped plate is on the basis of the original hanging board to increase a certain amount of production process.Use with hanging board.
1. Installation method of imitation masonry:
1. Make horizontal ink line at the initial position of installation.
2 imitation masonry installed from the bottom up, the first installation of imitation masonry (Yang) Angle, not bending of the Yin (Yang) Angle must be used in the middle of the line for up and down baking, heating softening can be folded into 90 degrees.
Seal the place where the back of the first piece of Yin (Yang) corner comes into contact with the wall with sealant, and align the bottom edge with the horizontal ink line, and then stick the right Angle with the wall after it is perpendicular to the corner, and finally nail it with steel nails in the place with circular nail marks.Specification: phi 2.0x20mm.
The second piece of Yin (Yang) good glue, especially the lower edge to be coated and pressed in the first piece of Yin (Yang) corner of the upper edge, overlap and then nail.And so on.